> PRODUCTS>VACUUM

VACUUM There are 75 products.

  • Vacuumjet Plug Ø2

    CV020812

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Plug Ø3

    CV030812

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Plug Ø4

    CV041012

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Plug Ø5

    CV051012

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Plug Ø6

    CV061212

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Plug Ø8

    CV081416

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Plug Ø10

    CV101616

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Plug Ø12

    CV121816

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Plug Ø14

    CV142006

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Plug Ø16

    CV162206

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Plug Ø20

    CV202606

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made....

    Brass bushing with an inner O’ring to prevent air loss when the vacuum is being made. With clamping tolerance. Incorporates a thread allowing removal of the bushing if needed.

  • Vacuumjet Seal Ø3

    JV030200

    Silicone seal to prevent air loss from the parting line.

    Silicone seal to prevent air loss from the parting line.

    Silicone seal to prevent air loss from the parting line.

  • Vacuumjet Seal Ø5

    JV050200

    Silicone seal to prevent air loss from the parting line.

    Silicone seal to prevent air loss from the parting line.

    Silicone seal to prevent air loss from the parting line.

  • Laminar Gas Vent

    LV483610

    Helps venting the mold cavity and the pneumatic ejection of the plastic part (allows air passing in both directions).Maximize performance installing at the end of the plastic flow.Supplied with 6 covers for maintenance purposes.Designed to work with VB and SV systems.

    Helps venting the mold cavity and the pneumatic ejection of the plastic part (allows...

    Helps venting the mold cavity and the pneumatic ejection of the plastic part (allows air passing in both directions).Maximize performance installing at the end of the plastic...

  • Non-rotating head for Ejec.Ø3

    NP030908

    Non-rotating head for ejector pins.

    Non-rotating head for ejector pins.

    Non-rotating head for ejector pins.

  • Non-rotating head for Ejec.Ø5

    NP050908

    Non-rotating head for ejector pins.

    Non-rotating head for ejector pins.

    Non-rotating head for ejector pins.

  • Non-rotating head for Ejec.Ø6

    NP061108

    Non-rotating head for ejector pins.

    Non-rotating head for ejector pins.

    Non-rotating head for ejector pins.

  • Non-rotating head for Ejec.Ø8

    NP081108

    Non-rotating head for ejector pins.

    Non-rotating head for ejector pins.

    Non-rotating head for ejector pins.

  • Keyed Tubular Base Ø6

    NR061208

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple to assemble and adjust.

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple...

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple to assemble and adjust.

  • Keyed Tubular Base Ø8

    NR081408

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple to assemble and adjust.

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple...

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple to assemble and adjust.

  • Keyed Tubular Base Ø10

    NR101608

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple to assemble and adjust.

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple...

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple to assemble and adjust.

  • Keyed Tubular Base Ø12

    NR122008

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple to assemble and adjust.

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple...

    Base for the tubular stepless that allows the pin to be fixed so it cannot turn. Simple to assemble and adjust.

  • Ejector Ø3x250

    PH130000-250

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø3x330

    PH130000-330

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø3x500

    PH130000-500

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø5x250

    PH150000-250

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø5x330

    PH150000-330

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø5x500

    PH150000-500

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø6x250

    PH160000-250

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø6x330

    PH160000-330

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø6x500

    PH160000-500

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø8x250

    PH180000-250

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø8x330

    PH180000-330

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Ejector Ø8x500

    PH180000-500

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

    Hardened ejectors with a simple retention method to minimize costs through reduced...

    Hardened ejectors with a simple retention method to minimize costs through reduced stock requirements in different diameters.

  • Pneumatic Piston

    PT182403

    Both of them are used to open the air valve to create a faster vacuum. Directly connected to the Vacuumjet unit through a circuit in the plate.

    Both of them are used to open the air valve to create a faster vacuum. Directly...

    Both of them are used to open the air valve to create a faster vacuum. Directly connected to the Vacuumjet unit through a circuit in the plate.

  • Pneumatic Piston - Angular

    PT183803

    Both of them are used to open the air valve to create a faster vacuum. Directly connected to the Vacuumjet unit through a circuit in the plate.

    Both of them are used to open the air valve to create a faster vacuum. Directly...

    Both of them are used to open the air valve to create a faster vacuum. Directly connected to the Vacuumjet unit through a circuit in the plate.

  • Smart Vacuumjet 60L

    SV605253

    This unit is able to create the Vacuum (60L/min) and blow-off (6bar) through the same channel.4 different Vacuum levels can be settled (-600 / -700 / -800 / -900mbar). Internal Electrovalve enable opening / closing of CUMSA Vacuum Valve. Allows automatic production.

    This unit is able to create the Vacuum (60L/min) and blow-off (6bar) through the same...

    This unit is able to create the Vacuum (60L/min) and blow-off (6bar) through the same channel.4 different Vacuum levels can be settled (-600 / -700 / -800 / -900mbar). Internal...

  • Connection Tube 1/4x50

    TV141650

    Allows connection of the main units to the ejection pin circuits, through different plates without air loss. Several units can be connected together to suit different needs.

    Allows connection of the main units to the ejection pin circuits, through different...

    Allows connection of the main units to the ejection pin circuits, through different plates without air loss. Several units can be connected together to suit different needs.

  • Connection Tube 1/4x75

    TV141675

    Allows connection of the main units to the ejection pin circuits, through different plates without air loss. Several units can be connected together to suit different needs.

    Allows connection of the main units to the ejection pin circuits, through different...

    Allows connection of the main units to the ejection pin circuits, through different plates without air loss. Several units can be connected together to suit different needs.

  • Double Action Vacuumjet

    VB607638

    This unit is able to create the Vacuum (60L/min) and blow-off (6bar) through the same channel. Vacuum is produced throughout the injection process. Blow-off is produced during the ejection process.

    This unit is able to create the Vacuum (60L/min) and blow-off (6bar) through the same...

    This unit is able to create the Vacuum (60L/min) and blow-off (6bar) through the same channel. Vacuum is produced throughout the injection process. Blow-off is produced during...

  • Vacuumjet + 60L

    VG523016

    This unit itself, extracts the air from the cavity through the ejector pins. Can be used to add more vacuuming power to the VJ (if needed). Also can be installed with the VM, to control the vacuum level.

    This unit itself, extracts the air from the cavity through the ejector pins. Can be...

    This unit itself, extracts the air from the cavity through the ejector pins. Can be used to add more vacuuming power to the VJ (if needed). Also can be installed with the VM, to...

  • Vacuumjet Unit 60L

    VJ600000

    Compact unit that creates a vacuum leading to negative pressure in the cavity. Only 6 Bars of air pressure from the injection machine needed. The vacuum can be made thru the clearance of the ejector pins and/or an air valve.

    Compact unit that creates a vacuum leading to negative pressure in the cavity. Only 6...

    Compact unit that creates a vacuum leading to negative pressure in the cavity. Only 6 Bars of air pressure from the injection machine needed. The vacuum can be made thru the...

  • Vacuum Control

    VM503032

    This unit allows to control the vacuum level in the cavity. Should be combined with the VJ or VG.

    This unit allows to control the vacuum level in the cavity. Should be combined with the...

    This unit allows to control the vacuum level in the cavity. Should be combined with the VJ or VG.

  • Spiral Ejector Ø6x150

    VP060527-150

    Ejector pins with spiral venting, that increase the vacuuming rather than regular ejector pins. Adjustment to be made from the back to maintain the spiral intact.

    Ejector pins with spiral venting, that increase the vacuuming rather than regular...

    Ejector pins with spiral venting, that increase the vacuuming rather than regular ejector pins. Adjustment to be made from the back to maintain the spiral intact.

  • Spiral Ejector Ø6x250

    VP060527-250

    Ejector pins with spiral venting, that increase the vacuuming rather than regular ejector pins. Adjustment to be made from the back to maintain the spiral intact.

    Ejector pins with spiral venting, that increase the vacuuming rather than regular...

    Ejector pins with spiral venting, that increase the vacuuming rather than regular ejector pins. Adjustment to be made from the back to maintain the spiral intact.